Single strand sprocket with one set of teeth around the circumference for applications where a single chain can support the torque and load
Pitch of 1/2 inch for size 40 chains
Ready-to-install finished bore with a wide hub on one side
Type B sprocket with a hub projection on one side to accommodate various types of bushings to help prevent sprocket from slipping on the shaft
Sprocket teeth hardened by electrical induction or flame to increase teeth durability against wear, lengthening the service life of the sprocket
This Tsubaki roller chain sprocket has a 1/2-inch pitch, fits size 40 chains, and is single strand with one set of teeth around its circumference for use with single strand chains. It is a Type B sprocket with a hub projection encircling the bore on one side and is ready for installation on a shaft of the appropriate diameter. The teeth of the sprocket have been hardened by electrical induction or flame, further increasing their durability against wear. It meets International Organization for Standardization (ISO) 9001 for quality assurance. This single strand roller chain sprocket is suitable for use in a broad range of applications involving light to moderate loads and ongoing, high-cycle operations, including vehicle transmission systems, construction and agricultural equipment, conveyors, and factory manufacturing and assembly lines, among others.
A roller chain sprocket is a thin wheel with deep, uniformly spaced teeth ringing its circumference. The distance from the peak of one tooth to the next is called the pitch, and is commonly measured in 1/8-inch increments. The sprocket transfers power and motion by a roller chain that is threaded over the teeth of the sprocket. The alignment of the chain with the sprocket’s pitch prevents the chain from slipping so that no power is lost. In the center of the sprocket is the bore (hole) for sliding the sprocket onto a shaft, and a bushing or bearing is often fitted to the sprocket s hub to custom-fit the sprocket onto a shaft to hold it firmly in place. A hub is a protruding, raised lip encircling the bore of the sprocket. Sprockets with hubs on both sides are Type C, sprockets with hubs on one side are Type B, and sprockets with no hubs are Type A sprockets. For applications requiring sprockets to be swapped onto shafts of different diameters, a sprocket with a bore large enough to fit all shafts can be used, with the gap between the bore and shaft closed with a bushing or bearing. Roller chain sprockets are used in a broad range of applications where the drive power of an engine needs to be transferred into motion, such as in motor vehicles, conveyors, escalators, agricultural, forestry and mining equipment, aeronautics, robotics and space exploration, among others.
U.S. Tsubaki Power Transmission manufactures a variety of chains, sprockets, and other power transmission components that meet International Organization for Standardization (ISO) standards for quality assurance. The company, founded in 1917, is headquartered in Wheeling, IL.
Product categories
- ATV Parts (7700)
- auto parts (276)
- Bicycle Parts (99)
- Car Parts (5654)
- CV Axle (700)
- Drift Trike Parts (10)
- Drive Clutch (1392)
- Clutch Accessories (923)
- Clutch Kits (212)
- Drive Clutch (154)
- Driven Clutch (103)
- Garden Parts (39)
- Go Kart Parts (406)
- Golf Cart Parts (4264)
- GY6-50CC Motorcyle Parts (426)
- Lawn Mower Parts (9297)
- Minibike Parts (537)
- Motorboat Parts (133)
- Motorcycle Parts (5868)
- OEM Parts (1476)
- Other Parts (622)
- Pickup Trucks (61)
- Scooter Parts (532)
- Snow Removal (293)
- Snowmobile Parts (885)
- Torque Converter 30 Series (13)
- Torque Converter 40 Series (5)
- Tracor Parts (23)
- Tractor & Trailer Parts (7)
- Tractor Parts (1389)
- Trailer (281)
- Truck (30)
- Uncategories (3)
- UTV Parts (2515)
Product tags
Air Filter
Axle
Ball Joint
Belt
Bracket
Brake cable
brake disc
brake disk
Brake Pads
Bushing
bushing block
Carburetor
car lamp
car light
centrifugal clutch
Clutch
clutch cable
dipstick
disc-brake
Disc Brakes
disk brake
Drive Belt
front fork
Gasket
holder
john deere l130 parts
John Deere shock
Lamps
Lift Kit
lights
liner bushing
lining
lowering kit
protective cover
Seat
shaft
Shock Absorber
sleeve bushing
Solenoid
solenoid valve
Switch
Throttle Cable
Tool
Washer
Water Pump
Related products
-
Go Kart Parts
75T 37.1mm #35 Blue and White Plated Sprocket
-
Go Kart Parts
50T 40mm #420 Blue and White Plated Sprocket
-
OEM Parts
11T 16mm #40 sprocket